Plumbing 101: Tips for Bathtub Installation
Plumbing 101: Tips for Bathtub Installation
Blog Article
We've uncovered this great article on Tools You Need to Install a New Bathtub listed below on the web and felt it made perfect sense to talk about it with you on this page.
Setting up a bath tub isn't precisely brain surgery, yet it does call for solid plumbing, carpentry, and occasionally, tiling skills. Replacing an old bath tub with a new one is also a moderately hard task. If the old tub is conveniently easily accessible, the task can relocate immediately; if you have to open up a wall to eliminate the old bathtub and also place the brand-new tub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will need an assistant to leave the old bathtub and set in the new one. Ensure you have qualified on your own for the job and also fit trying it. Instead of hiring a service provider to take over a halfway-completed project, it is far better to consider utilizing one prior to you start. Chances are you might require an expert plumber to make tube links.
This article will certainly assist you mount a brand-new bath tub in your bathroom if you have actually currently gotten a new tub and don't require to change the plan of your previous water supply pipelines.
Your tools as well as product list ought to consist of the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, then the first thing you must do is disconnect the water supply. After doing so, switch on the taps to drain pipes any type of water staying in the system. The process of removing the existing faucets can be quite troublesome as a result of the restricted access that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a towel prepared for the staying water that will certainly come from the pipes. As soon as the supply pipelines have actually been removed, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from turning during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Prior to moving on to fit the new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic port to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washing machines remain in area between the tap and also the sink. Protect the faucet in place with the maker offered backnut. As soon as the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former kind needs to be connected to the tap finishes initially, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bath tub
Using the two wooden boards under its feet, place the bath tub in the called for position. The wooden boards are practical in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four little points.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level and also adjusting the feet on the bath tub until the spirit level reviews degree.
To install faucets, fit the bottom of the outermost flexible faucet port to the ideal supply pipe by making a compression join; after that do the very same for the other tap.
Switch on the water as well as check all joints and also new pipework for leakages as well as tighten them if necessary. Fill up the tub and additionally examine the overflow outlet and also the normal outlet for leakages.
Finally, repair the bath paneling as described in the supplier's user's manual. Tiling and securing around the bathtub needs to wait until the tub has actually been utilized a minimum of once as this will resolve it right into its final position.
Preparing for the Installation
First of all, the sustaining frame supplied with the bath must be fitted (if called for) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to make sure that if the tap features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the versatile tap adapters to the bottom of both faucets making use of 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently prepare to be suited its final placement.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to split a rigid seal, triggering the water to pass through the wall in between the bath and the tiling, leading to complications with dampness and also feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and fittings. They are offered in tubes as well as cartridges, and also are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of drenched newspaper or soft rope. Bear in mind to constantly load the tub with water prior to securing, to permit the motion experienced when the bathtub is in use. The sealant can crack rather early if you do not consider this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise quickly available on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you liked our topic on How to Install a Bathtub. Thanks for taking a few minutes to read our blog. So long as you enjoyed our blog post if you please make sure you remember to share it. I truly appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Reliable plumber? Dial now! Report this page